Shutdown Project

Welding Inspector -Shall be responsible for all inclusive but not limited to: 1. To maintain, on a daily basis from the start of fabrication, a QC record detailing fabrication, material traceability, welder and welding procedure identification, non-destructive testing records, heat treatment details and hydro test records. These records are to be completed daily and reflect the exact status of weld production, welder record, NDT, Stress relieving and hydro test completion. 2. Assure the availability and control of the NDT Personnel for the project. 3. Compile and present pipe work as-built documentation and QC records prior to equipment commissioning. 4. Ensure that all materials allocated for the project, including welding electrodes, are correctly identified, properly stored, correctly allocated and handled to avoid damages. 5. Ensure that the relevant welding procedures are adhered to and that all welders are qualified for the particular process being used. Coordinator - Site QA/QC -Shall be responsible for all inclusive but not limited to: 1. Coordinate all QA/QC Activities between Contractor Area QC Supervisors/Welding Inspectors with QatarEnergy Inspection 2. Coordinate with QatarEnergy Job Officers for Pre-Inspection Checklist & IPF 3. Ensure that Pre-Inspection Check List is attached with all IPF's 4. Make sure that, 1st copy of all approved Pre-Inspection Check lists are submitted to QatarEnergy TA Planning Team every two hours 5. Ensure that there is no delay in any inspection activities and that all Inspections are carried out in strict compliance with the agreed TA schedule 6. Ensure that, enough NDT personnel are available at the site of requirement without any delay 7. Ensure that all correct procedures are available at Work Sites 8. Ensure that all Welder Certifications and Qualifications are available at site for inspection of competent authorities at any point of time 9. Seamless job continuity through effective coordination with all concerned Mechanical QC Inspectors -Shall be responsible for all inclusive but not limited to: 1. Coordinate all QA/QC Activities between Contractor Area QC Supervisors with Site QC Coordinators on behalf of QatarEnergy Job officers/Planning team 2. Perform and ensure that, all Pre-requisites are completed before Job Officer is requested for Pre-inspection Checking of equipment 3. Attach Pre-Inspection Check List to all IPF's and forward to Site QC Coordinators 4. Carryout smooth delivery of all inspection activities in strict compliance with the agreed TA schedule 5. Check and verify all correct gasket specifications, flange bolts tighness, flange correct bolts installation at site during spading and de-spading activities 6. Check and Ensure all PSSR and Flawless activities are performed as per Qaulity requirement 7. Maintain records of all critical activities on daily basis and submit report to QatarEnergy Job officers and Planning team 8. Seamless job continuity through effective coordination with all concerned Manager (QC) – Quality Control Manager Department: Quality Control | Industry: Oil & Gas / Refinery / Shutdown Job Responsibilities - Manage and supervise all Quality Control activities during shutdown, maintenance, repair, piping, and fabrication works. - Implement the approved Quality Control Plan (QCP), Inspection and Test Plans (ITPs), and project quality procedures. - Ensure compliance with project specifications, approved drawings, and applicable international codes and standards. - Coordinate with client representatives, construction teams, QA/QC engineers, inspectors, and third-party inspection agencies. - Review welding procedures (WPS/PQR), welder qualifications, NDT reports, and inspection documentation. - Monitor welding, piping, fabrication, pressure testing, and mechanical completion activities. - Manage non-conformance reports (NCRs), corrective actions, and quality audits. - Ensure all inspection records, test packages, and quality dossiers are completed and submitted on time. Qualifications and Experience - Bachelor’s degree or Diploma in Mechanical Engineering. - Extensive experience in QA/QC management within oil and gas, refinery, petrochemical, or shutdown projects. - Strong knowledge of welding, piping, fabrication, NDT, inspection procedures, and quality documentation. - Experience coordinating with clients and managing inspection teams. - Relevant QA/QC or welding inspection certification preferred or as required by the client. Welding Inspector Department: QC / Welding | Industry: Oil & Gas / Shutdown Job Responsibilities - Inspect welding activities at different stages, including fit-up, root pass, intermediate passes, and final welding. - Verify joint preparation, alignment, root gaps, bevel angles, and welding consumables. - Ensure welding is performed according to approved WPS, PQR, and qualified welder requirements. - Conduct visual inspection of welds to identify cracks, porosity, undercut, overlap, and other defects. - Verify welding parameters, preheating, interpass temperature, and post-weld heat treatment (PWHT), where applicable. - Coordinate radiographic testing (RT), ultrasonic testing (UT), magnetic particle testing (MT), and liquid penetrant testing (PT). - Review NDT reports and ensure defects are repaired and re-inspected. - Maintain weld maps, inspection reports, consumable records, and welding documentation. - Ensure compliance with applicable ASME, AWS, API, and project-specific standards. Qualifications and Experience - Diploma or Degree in Mechanical Engineering or a relevant technical discipline. - Relevant experience in welding inspection for oil and gas, refinery, piping, or shutdown projects. - Good knowledge of welding processes, WPS/PQR, welder qualification records, and NDT methods. - CSWIP 3.1, AWS CWI, or an equivalent client-approved certification may be required. Engineer QA/QC – Quality Assurance / Quality Control Engineer Department: QA/QC | Industry: Oil & Gas / Refinery / Shutdown Job Responsibilities - Implement project QA/QC procedures, quality plans, and inspection schedules. - Review drawings, specifications, method statements, and Inspection and Test Plans (ITPs). - Coordinate inspections for piping, mechanical equipment, fabrication, welding, and installation. - Ensure work complies with approved project specifications and applicable codes. - Coordinate with construction teams, client inspectors, and third-party inspection agencies. - Review inspection requests, NDT reports, material test certificates, and pressure-test records. - Raise and follow up on NCRs, corrective actions, and preventive measures. - Prepare daily inspection reports, quality records, and handover documentation. - Monitor quality performance and support audits and mechanical completion activities. Qualifications and Experience - Bachelor’s degree or Diploma in Mechanical Engineering. - Relevant QA/QC experience in oil and gas, refinery, petrochemical, or shutdown projects. - Knowledge of ISO 9001 quality systems, ITPs, method statements, and inspection documentation. - Familiarity with piping, welding, mechanical equipment, and NDT requirements. - Relevant QA/QC certifications are an advantage or may be required by the client. QA/QC Inspector – Welding Department: Welding QC | Industry: Oil & Gas / Shutdown Job Responsibilities - Perform visual inspection of weld joints before, during, and after welding. - Verify fit-up, joint preparation, alignment, root gap, and welding consumables. - Check weld quality against approved WPS, project specifications, and applicable codes. - Verify welder identification, qualification records, and welding parameters. - Coordinate NDT activities and review RT, UT, PT, and MT reports as assigned. - Inspect repaired welds and ensure defects are corrected before acceptance. - Maintain weld inspection reports, weld maps, inspection requests, and quality records. - Coordinate with welding supervisors, construction teams, and client inspectors. - Ensure all welding activities comply with approved inspection procedures and acceptance criteria. Qualifications and Experience - Diploma or Degree in Mechanical Engineering or a relevant technical qualification. - Relevant experience in welding inspection for oil and gas, piping, fabrication, or shutdown projects. - Knowledge of WPS/PQR, welder qualifications, welding defects, and NDT procedures. - CSWIP 3.1, AWS CWI, or an equivalent certification may be required, depending on client criteria. Flawless QC Inspector Department: Quality Control | Industry: Oil & Gas / Refinery / Shutdown Important: “Flawless QC Inspector” is not a universally standardized job title. The following is a proposed JD for a QC inspector focused on defect prevention and first-time-right quality. Confirm the exact scope with the Qatar client. Job Responsibilities - Monitor site activities to ensure work is completed correctly the first time, minimizing defects and rework. - Conduct detailed inspections of piping, welding, fabrication, mechanical installation, or other assigned work. - Identify workmanship defects, deviations from approved drawings, and non-compliance with project specifications. - Verify material identification, traceability, dimensions, fit-up, and inspection status as applicable. - Ensure all required inspections and tests are completed before work proceeds to the next stage. - Coordinate with welding inspectors, QA/QC engineers, supervisors, and client representatives to resolve quality issues. - Track defects, repair activities, repeat failures, and corrective actions. - Maintain inspection checklists, quality reports, and defect-tracking records. - Support quality audits, final inspections, punch-list clearance, and project handover. - Promote compliance with approved procedures and applicable project quality standards. Qualifications and Experience - Diploma or Degree in Mechanical Engineering or a relevant technical discipline. - Relevant QC experience in oil and gas, refinery, petrochemical, or shutdown projects. - Knowledge of inspection procedures, drawings, project specifications, defect identification, and quality documentation. - Welding inspection or NDT knowledge may be required depending on the assigned discipline. - Client-approved inspection certification and experience requirements must be confirmed